Q-Scan PC/DMX Professional Scanning and Graphics System For Q-Series Beam Projectors and other Beam aperture devices with a standard ¾”
At any given moment, only a bright laser dot is actually projected. The apparent continuity or lines drawn are due to persistence of vision. The dar
Note: Clicking any Brown Mode button automatically sends the ON and SYNC command. (0) DMX Digital Value DMX Controller Fader
Before using , click to see how the pattern will be saved. Starting with a perfect circle, slow down one wave then put it back. You should notice t
(16) DMX Digital Value DMX Controller Fader 1 Generates patterns based on circle A orbiting circle B. A circle is drawn that moves around the perim
(32) DMX Digital Value DMX Controller Fader 1 Generates a horizontal fan using a linear ramp. A horizontal line is drawn using a linear ramp with
(48) DMX Digital Value DMX Controller Fader 1 Generates a horizontal in-line sequence of 16 beams. A horizontal sequence of 16 beams is displayed
Mode 8 Continued The 6th fader controls the binary beam mask (Beam Mask). If fader 6 is set to zero then no beams will be shown and if set to max 25
(88) DMX Digital Value DMX Controller Fader 1 Generates 8 different tunnel patterns that are sound sensitive. Use the Select1 through Select8 but
(96) DMX Digital Value DMX Controller Fader 1 Displays 1 of 8 preloaded text lines stored in the laser unit memory. Use the Select1 through Select8
Scenes Section Continued If the Q-Scan Expansion Set is not attached then the laser defaults to a selection of 1 animation and 7 stills selected by t
Table of Contents Section 1.0 = Introduction – Q-Scan PC/DMX Section 2.0 = System Orientation – Q-Scan PC/DMX Section 3.0 = DMX-512 Operation – Q-Sc
Functions The Set Text button opens a small setting box with 6 labeled faders and 4 buttons. Center: Allows you to place the text at different h
Typically, you type a sentence, click XferText button, select Xfer#1. Then erase that line and type a new line. This time select Xfer#2. The Helper wi
Example: (Give it a Try) Click the first Mode button, set the faders and click Record 1. Click the next Mode button, set the faders and click Record
At the Bottom of the screen you should be able to see a blue bar with some buttons on it. This is the Script Editor and Control bar. To use or creat
The Show Text command buttons can NOT be scripted because they are not true modes. To add scripted text to your show you must first upload the desired
Sound Graphics Editor Continued The Graphic always starts in the center with the laser beam off. This is seen as a dull gray line to the first visi
Sound Graphics Editor Continued This technique is how you rough draw the image desired, then select each point and move it to the desired location
Sound Graphics Editor Continued Every point in the graphic can be defined for direction and amount. This allows you to design Mobile Graphics such as
With the Q-Scan Expansion Set: If the memory module is attached then the selected group/scene will be played. It can be interrupted, mid scene, to do
QSCAN DMX SPECIFICS FOR ALL 8 CHANNELS VS MODES: Modes Base Base +1 Base +2 Base +3 Base +4 Base +5 Base +6 Base +7Circle Patterns 0>7 XYS
Congratulations on purchasing one of the most versatile laser projection systems available in today’s laser industry. Keeping with the tradition o
QSCAN DMX SPECIFICS FOR ALL 8 CHANNELS VS MODES: (Ctn’d) Option 8=224>255 Where ">" means "through" above. Note: Animation
Each Q-Scan PC comes with a special adapter called a SIKA cable. This cable must be placed between the Q-Scan and the computer. You may extend th
IBM 25 PIN female QSCAN MALE 9 pin 3..RECEIVE---<----red-----------<---------XMIT 3 2..SEND------>-------yel-------->---------REC
• Step Ten –Go to beginning of the manual and begin the learning and set up of the system. Illustration of proper alignment Proceed to Sect
4. Servicing Do not attempt to service this system yourself as opening the unit can expose you to dangerous voltage. Qualified OmniSistem technician
Note: If Audio and Mic are both used then sound adjust controls balance. DMX functions selected via the base address: MODE: DECIMAL: Circle P
Place character 255 (square block) at end of line for termination. This will erase any text that appears to the right of the text block. Moving mode
COM PORT SETUP: On First activation you will need to select an active comport for the PC. This Program will Automatically disable some choices becau
If you can figure out which one is the Mouse port. DON’T CHANGE IT. You are trying to enable or move the com port that is NOT assigned to the MOUS
• Text. Simple laser text messages are projected on a flat surface to be read by the audience. • Animations Still pictures and moving pictures such
The Fast Pad button enables a small black window. When the mouse is inside this window, the 2nd and 3rd faders are forced (fast) to a setting relativ
Comments to this Manuals