DESIGN 150 PRO PR-1151 This product manual contains important information about the safe installation and use of this projector. Please read an
Design 150 PRO EN doc 10/26 DMX AddressOperation ModeOption SettingInformationTest ModeUser MemoriesTime ModesLight Level SensorTime ClockLamp Man
Design 150 PRO EN doc 11/26 z SUBMENU ¦ DMX Address DMX Address XXX(001~512) ¦ Reset Are You Sure?
Design 150 PRO EN doc 12/26¦ Operation Mode Mode = DMX Operation Select Memory Preset Memory 1 Select Memory Preset Memory 2
Design 150 PRO EN doc 13/26¦ Option Settings Lamp Control By Power On Lamp Control By Control Channel Option Lamp Control Lamp
Design 150 PRO EN doc 14/26¦ Information Display Lamp Hours Lamp Hours =XX XX is the lamps elapsed time(Press DOWN&UP&ENTER button to the ne
Design 150 PRO EN doc 15/26¦ User Memories Dimmer DimmerXXX XXX(001~255) Color (Overrides CMY) ColorXXX XXX(001~255) Cyan CyanXXX XXX(001~255) Ma
Design 150 PRO EN doc 16/26Yellow Yellow XXX XXX(001~255) Reset User Memory 1 Reset User 1 ? <Unlock> 2 3 & 4 (Press UP/DOWN/ENTER but
Design 150 PRO EN doc 17/26¦ Timer Modes Timer Modes Always On Timer Modes On / Off Timer Modes Use Start / Stop Start 1 = Po
Design 150 PRO EN doc 18/26¦ Light Level Sensor Set To Current Light Level Current On Level Set to - XX Light Level On Set Point Set By Ente
Design 150 PRO EN doc 19/26 z How to use Timer Modes to control the projector? If the user needs to switch on
Design 150 PRO EN doc 2/26 SECTION PAGE SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 FITTING THE LAMP 4 POWER CONNECTIONS 5 CONTROL
Design 150 PRO EN doc 20/26 If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in an
Design 150 PRO EN doc 21/26LIGHT OUTPUT
Design 150 PRO EN doc 22/26 VOLTAGES: 100/120/200/220/230/240V AC, 50Hz or 60Hz POWER CONSUMPTION: 200W @ 220V LAMP: Type : CDM
Design 150 PRO EN doc 23/26 ELECTRICAL DIAGRAM
Design 150 PRO EN doc 24/26 NAME PART NO. NUMBER REMARK TRANSFORMER 040030038 1 100~245V 50/60Hz THERMOSTAT 190010054 1 95°C/10A/250V CAPACITOR 1
Design 150 PRO EN doc 25/26
Design 150 PRO EN doc 26/26 PR LIGHTING LTD. No. 571, Yingbin Road, Dashi, Panyu, Guangzhou, China Post-Co
Design 150 PRO EN doc 3/26 When unpacking and before disposing of the carton check there is no transportation damage before using the projector. K
Design 150 PRO EN doc 4/26 The unit was designed to make installation easy: it can be fitted on a floor, wall or ceiling as required and will ope
Design 150 PRO EN doc 5/26 Use the power cord provided to connect the mains power to the projector. The user can connect by yourself what you nee
Design 150 PRO EN doc 6/26 In the Controller mode, the DMX output has to be connected with a DMX terminator at the last fixture in the chain. This
Design 150 PRO EN doc 7/26 The Design 150 PRO uses 7 DMX channels. They are listed in the following table. CHANNAL FUNCTION DMX VALUE DESCRI
Design 150 PRO EN doc 8/26 Each Design 150 PRO must be given a DMX start address so that the correct projector responds to the correct control sig
Design 150 PRO EN doc 9/26 Green: ON —— DMX signal OK or in the Master mode; OFF —— No DMX signal; Flash ——DMX error; Blue:
Comments to this Manuals